BEYEM PAVIDREN is a decorative continuous draining pavement with a natural appearance to be laid “in situ”.
BEYEM PAVIDREN consists of a mixture of selected pebbles and a resin mixture specially developed to agglomerate these pebbles.
Particularly suitable for exteriors.
- Draining.
- Easy to clean. Minimal maintenance.
- Simple application.
- Full integration into the environment.
- Unalterable colour.
- Does not generate mud, dust or water run-off areas.
- High resistance to weed growth.
- Interior and exterior.
- High abrasion resistance.
- Maximum slip resistance.
- Variety of colours and aggregates sizes.
Decorative drainage pavement for landscaped walkways, tree surrounds, swimming pool solariums, playgrounds, terraces, pedestrian accesses to houses, roundabouts, sports centres, campsites, rural and agricultural roads, medians, etc…
Useful supports for the application of BEYEM PAVIDREN are among others:
- Concrete-based floors.
- Surfaces where you need to avoid puddles of water and liquids.
Supports must be rigid.
The substrates must be clean, dry, hard and free of dust or particles that hinder adhesion.
The surface must be prepared with the necessary slopes to evacuate water in order to avoid retention and accumulation under the pavement.
Pour two sacks of pebbles into a suitable recipient. Add the supplied quantity of Pavidren Special Resin, previously mixing both components together. Mix with a mixer at low revolutions until completely homogenised (approximately 5 minutes). A maximum time of 1 hour after mixing is available to apply the pavement. This time may vary depending on the temperature and humidity conditions. Once the support has been prepared, pour the mixed product, and spread it with a ruler until the desired thickness is obtained (a minimum thickness of 3 cm is recommended). Compact with the help of a trowel or similar.
Pedestrian traffic: 24-48 hours.
Final curing takes place after 7 days of application.
- Do not apply below 10°C and not above 30°C.
- Protect fresh surfaces from direct sunlight, frost and air currents.
- Do not re-mix the product after it has started to harden.
- Do not mix more material than can be applied within the workability period or pot life of it.
- Clean periodically, depending on the filling of the pores, with pressurised water.
- The particle sizes and drainage capacity may vary depending on the pebbles used.
- The waiting time for traffic may be reduced or extended depending on environmental conditions.
| Product identification and application data | |
| Appearance | Coloured aggregate |
| Colour | White, Nevada Grey, Grey, Ivory, Wood, Alicante Red and Green. |
| Grain size ranges | 3-6 mm, 6-9 mm, 9-12 mm |
| Minimum thickness | 30 mm |
| Maximum thickness | 60 mm |
| Performance | ≈ 1,25 m² of 3 cm thickness for each unit used. The unit consists of 60 kg of aggregate (30 kg + 30 kg) and 1,8 liters of Pavidren Special Resin (1,35 L Component A + 0,45 L Component B) |
| Tariff code | 3506.99.90 |
| Final performance | |
| Type | Draining pavement |
| Draining capacity | ≥ 800 l/m²min |
| Putting into service | 24-48 h |
| Flexural strength | ≥ 5,5 N/mm² |
| Compressive strength | ≥ 3,5 N/mm2 |
| Slip resistance Rd | > 45 (Class 3) |
BEYEM PAVIDREN is packaged in 30 + 30 kg plastic bags and 1,8 litre bicomponent resin pots. Conservation: 12 months in sealed original packaging, protected from humidity and in a covered place.
Equipment and tools are easily cleaned with water before the product has hardened. Cured or hardened product can only be removed by mechanical means.
The execution of the decorative continuous drainage paving with a maximum thickness of 60 mm will be carried out with the natural aspect paving Beyem Pavidren, from the company Rodacal Beyem, suitable for making uniform and stable decorative floors. Apply on a previously prepared, clean and dimensionally stable substrate.
For any information concerning safety issues in the use, handling, storage and disposal of chemical residues, users should consult the most recent version of the MSDS for the product. Disposal of the product and its packaging must be carried out in accordance with current legislation and is the responsibility of the final consumer of the product.
