Beyem Neocal Fino NOx

BEYEM NEOCAL FINO NOx is a photocatalytic, with self-cleaning and decontaminating properties, fine,  rendering and plastering lime mortar. Formulated with mixed binders, lime, selected white aggregates, photocatalytic reagents and special additives. Fine scraping, trowelled, burnished and smooth finishing. Especially suitable for rehabilitation of historic and/or protected buildings.

• Suitable for spray render and pump machines or manual applications.

  • Mechanical strengths corresponding to lime mortars.
  • Decontaminating and self-cleaning effect.
  • High water vapour permeability. Allows the wall to breathe.
  • Great plasticity.
  • Compatible with old masonry brickworks/walls.
  • Great variety of finishes.
  • Rainwater- proof. Weather resistant.
  • Suitable for internal  or external walls.
  • New construction and building rehabilitation.
  • Mineral product.

Photocatalytic, through-coloured, fine,  lime rendering and plastering mortar for both building rehabilitation and new construction. Self-cleaning and decontaminating coating.

BEYEM NEOCAL FINO NOx degrades organic and inorganic substances deposited on its surface, which helps to maintain its aesthetic quality over time.

BEYEM NEOCAL FINO NOx reduces the concentration of most of the pollutants present in urban areas, turning harmful gases into compounds that are safe for health and the environment, through a natural process free of chemical agents.

Especially suitable for fine  and smooth finishes in rehabilitation of historic and/or protected buildings. Facade  protection. Suitable for walls and ceilings both in interior and exterior situations, manually or mechanically. Especially suitable  as a finish coat  for BEYEM NEOCAL BASE  basecoat.

BEYEM NEOCAL  FINO  NOx is  suitable for:

• Old lime mortars with good mechanical strength and adhesion. BEYEM NEOCAL BASE  undercoat.
• Cement based  renders and mortars. 

Substrates must be clean, compact and free of substances that reduce adhesion such as dust, oil, grease and with no loose material. Substrates must submit an adequate porosity and surface roughness. Uneven areas must be corrected. Dampen substrates with water to cool down if they should be too warm, in case of wind or over absorbent substrates and wait until the thin layer of water disappears. It is a good practice curing with a fine spray of clean water 24 h after application. Curing operation is essential to avoid  rapid drying and depends on the degree of porosity and surface absorption. Do not apply on cellular concrete, gypsum-based plasters, paint, metal surfaces, plastic, surface waterproofing products  or materials with low mechanical properties.

Mix manually or mechanically BEYEM NEOCAL FINO NOx with 5,0-5,5 l per bag of clean water until a homogeneous, creamy and lump-free paste is obtained. Let the mix stand for 5 minutes before application. To apply with render  spray machine, it´s necessary to set the relation water/mortar  and pump pressure depending on section and length of hose  and climatology conditions. It´s important to maintain the  variables affecting the properties of the applied mortar (distance to the wall, angle of application and water proportion).

Spread the mixed product with a trowel (in case of manually or mechanically application) leaving  4-6 mm of average  thickness depending on the desired finish. Press to ensure adhesion and expel the air contained in the pores. Smooth with a ruler the applied material to regulate thickness. When BEYEM NEOCAL FINO is green (set but not fully hardened) it should be finished using the appropriate tool  depending on the desired texture (trowelled, fine scraping…). Time until finishing depends of substrate, temperature and humidity. 

• Always mix with the specified amount of water.
• Do not apply below 5ºC or above 30ºC.
• Do not apply when there is risk of frost, rain, strong wind or direct sunlight.
• It is not advisable to apply on horizontal or sloped surfaces in exterior situations.
• Protect top edges of facade from rainwater penetration.
• Do not apply directly on brickwork,  concrete blocks…
• Lime mortars have a slower setting, so the hardening time increases.
• The minimum finishing thickness of system (Beyem Neocal Base + Beyem Neocal Fino)  must be 10 mm, to contribute actively to the  waterproofing of surface.
• Expansion joints should be included as required by the substrate and respected by all applied materials.
• Reinforcement with alkali resistant fiberglass mesh  may also be required, dependent upon substrate condition ( junctions of different surfaces, corners of voids…),  project specification or applied thickness greater than recommended.
• Variations in weather conditions during application, and the application in several phases can produce changes in tone.
• The photocatalytic properties of the mortar remain  whenever the surface of the coating is not covered.
• The effectiveness of the photocatalytic process is influenced by the degree of exposure to light.

BEYEM NEOCAL  FINO  NOx  is packed 25 kg plastic lined paper bags.

Storage: when stored unopened in a cool dry place, shelf life is 12 months from date of manufacture.

Tools can be cleaned easily with water before the product hardens. Hardened product can be removed only mechanically.

Facade rehabilitation and photocatalytic with self-cleaning and decontaminating coating, must be carried out with a breathable, through-coloured, external decorative, fine, lime mortar breathable and rainwater-proof rendering lime mortar compliant with EN 998-1 Class CR CSII W_c 2, such as BEYEM NEOCAL FINO NOx manufactured by Rodacal Beyem Company. Coverage will be ≈ 1,4 kg/m² per mm of thickness. The substrate must be clean, sound, compact and dimensionally stable. Expansion joints must be respected.

For further and complete information about the safe use of our product please refer to our latest version of the Safety Data Sheet, which is available upon request.

Disposal of the product and packaging must be in accordance with current legislation. This is responsibility of the final product user.