About this product
Benefits
Use
Substrates
Preparation of substrates
Instructions for use
Recommendations
Technical data
Packaging
Cleaning tools
Project specification
Health and Safety
Certifications
About this product
BEYEM FIR BLANCO is an enhanced cement based tile adhesive for interior use, formulated with white cement, selected aggregates and special additives to improve workability and adhesion. No vertical slip. Allows adjustment of tiles. Indoor environment quality. Classifed as A+ class according to Décret nº. 2011-321 (France).
Benefits
- Great plasticity.
- High water retentivity. Highly thixotropic.
- High tensile adhesion strength and mechanical strength.
- Long open time. Allows adjustement of tiles.
- No vertical slip.
- Very low VOCs emissions.
Use
Laying of ceramic tiles of medium/high absorption in interior walls and floors. Especially suitable for laying ceramic tiles of small and medium format and IIb / III group.
Substrates
BEYEM FIR BLANCO is suitable for:
- Cement based substrates.
- Cement based renders /plasters and screeds.
- Concrete floors.
Preparation of substrates
Substrates must be clean, compact and free of substances that reduce adhesion such as dust, oil, grease and with no loose material. Uneven areas must be corrected with suitable smoothing and finishing products. Substrates must be free from any rising damp and have already completed the curing period of hygrometric shrinkage. Dampen substrates with water to cool down if they should be too warm, in case of wind or over absorbent substrates and wait until the thin layer of water disappears. Do not use on gypsum based plasters or paint.
Instructions for use
Mix manually of mechanically BEYEM FIR BLANCO with 6,75-7,75 l per bag of clean water until a homogeneous, creamy and lump-free paste is obtained. Let the mix stand for 5 minutes before application.
Small tiles must be fixed using a notched trowel of 6×6 mm. For tiles sizes greater than 400 cm2, a notched trowel 8×8 mm must be used. Spread the mixed product onto the substrate to a maximum surface area of 1 m2 or no more than can be tiled within 20/30 minutes in normal conditions. Unfavorable environmental conditions (strong sunlight, drying wind, high temperature as well as a highly absorbent substrate), could drastically reduce this time to a few minutes. Bed the tiles firmly into the adhesive with a slight sliding and/or twisting action, to ensure a good contact and complete coverage.
It is good practice to lift an occasional tile after fixing, to verify that the required contact is being achieved. Back of the tile must be completely wet.
Recommendations
- On gypsum substrates, apply BEYEM FIJADOR primer before , to avoid contact between gypsum and the cement of the adhesive, avoiding adverse reactions.
- Do not apply on plastic, metal or wood.
- Do not apply below 5ºC or above 30ºC.
- Do not apply when there is risk of frost, rain, strong wind or direct sunlight.
- Leave joints between tiles with a minimum width of 2 mm. Grout with BEYEM JUNTA UNIVERSAL / BEYEM JUNTA EXTRAFINA.
- On floors with a surface area greater than 30 m2 , it is recommended to leave separation or sealing joints filled with a deformable material.
- On interior floorings larger than 15 m2, it is advisable to keep a free perimeter expansion joint between the floor and the wall or pillar, hidden by a skirting board (of approximately 5 mm).
Technical data
Product identity. Properties of mixture and application data |
|
Appearance |
Powder |
Color |
White |
Bulk density |
≈ 1270 Kg/m3 |
Density of the mix |
≈ 1700 Kg/m3 |
Grading |
0-600 µm |
Mixing water,% |
± 29% |
Pot life |
≈ 2 h |
Adjustability time |
≥ 20 min |
Grouting |
≈ 24 h |
Coverage |
≥ 3 Kg/m2 |
Tariff code |
3824.50.90.00 |
Final performances |
|
Type |
Annex ZA EN 12004 |
Initial tensile adhesion strength |
≥ 0,5 N/mm2 |
Tensile adhesion strength after water immersion |
≥ 0,5 N/mm2 |
Total VOCs (28 days) |
< 500 µg/m3 |
Packaging
BEYEM FIR BLANCO is packed 25 kg plastic lined paper bags.
Storage: when stored unopened in a cool dry place, shelf life is 12 months from date of manufacture.
Cleaning tools
Tools can be cleaned easily with water before the product hardens. Hardened product can be remove only mechanically.
Project specification
Laying of ceramic tiles must be carried out with cement based adhesive compliant with EN 12004 – Annex ZA, such as Beyem Fir Blanco manufactured by Rodacal Beyem company. The substrate must be compact, free from any flaky, loose parts and must be clean and cured, having already completed the shrinkage stage. Existing joints must be respected and elastic fractionizing and perimeter joints must be created. Ceramic tiles must be laid with joint-gap spacers with a width of ___ mm.
Health and Safety
For further and complete information about the safe use of our product please refer to our latest version of the Safety Data Sheet, which is available upon request.
Disposal of the product and packaging must be in accordance with current legislation. This is responsibility of the final product user.
Certifications
Reviews
There are no reviews yet.