Beyem Cril

BEYEM CRIL is an acrylic mortar coloured with pigments of high resistance and light fastness for decorative finishing of BEYEM ETICs system.

It comes in three finishes:

• Thick 2.5 kg/m²
• Thin 2 kg/m²
• TX 2-2.5 kg/m²

Provides resistant, elastic, waterproof and high covering power finishes. Allows application on large surfaces without working joints.

• Impermeable to rainwater and permeable to water vapour
• Flexible: high deformation capacity. Low modulus of elasticity
• Semi-elastic (anti-cracking)
• Excellent workability
• High adhesion
• Low maintenance
• Ready to use
• Different finishes: Thin, TX, Coarse
• Includes anti-mould preservatives

Decorative coating for ETICs. Anti-crack system in conjunction with other BEYEM products.

The useful supports for the application of BEYEM CRIL are:

BEYEM ETICs system:

BEYEM ADHETERM, BEYEM CRIL FONDO

Other BEYEM products

BEYEM R1T RENODUR, etc… (Anti-cracking system)
BEYEM S-BLANCO, BEYEM S-GRIS, BEYEM IMPER.
In cases not described consult the Technical Department.

The aforementioned substrates must be sound, clean, free of paint residues, poorly adhered parts or substances that may hinder adhesion. All substrates must have adequate flatness. The substrate must not have clear problems of dampness and, where appropriate, must have completed its curing shrinkage and its maturing period must have been respected.

At least 6 hours after applying Beyem Cril Fondo, apply Beyem Cril with a stainless steel trowel, spreading the product uniformly over the surface. Once the product has lost its tackiness on the tool, proceed to finish the surface with a trowel or trowel.

• Do not apply at temperatures below 5°C or above 30°C, or when humidity exceeds 75%.
• Do not apply if there is a risk of frost, rain, strong winds or direct sunlight.
• Keep containers tightly closed after use.
• Conditions of high humidity and/or low temperatures may prolong drying time and cause loss of colour uniformity. The same may occur with high temperatures or strong winds, as these reduce drying time. This is particularly important if the work extends across different seasons or if there is a break in the work. The execution of the work should be planned to minimise this risk.
• Avoid using different batches on the same surface; if this is not possible, it is advisable to mix the contents of the second container with the first once 50% of the first has been used. This will prevent any slight variations in shade between batches from affecting the final result.
• It is recommended to cover the scaffolding with fabric or tarpaulins to protect the surface after application from wind, rain or intense sunlight (approx. 2 days in favourable weather conditions).
• Avoid leaving a section half-finished to prevent joints. Use working joints if necessary.
• This product is not suitable for protecting horizontal or sloping surfaces where water may pool.
• We do not recommend using colours with a solar radiation absorption coefficient (α) greater than 0.7, unless the façade is permanently shielded from solar radiation.
• Protect the upper edges of the cladding against rainwater penetration.
• Due to the existence of a large number of mould species and varying climatic conditions, in some cases the additives used cannot guarantee the complete elimination or prevention of the proliferation over time of certain plant microorganisms.
• Observe expansion joints.
• Product recommended for expert users. 

BEYEM CRIL is packaged in 25 kg plastic buckets.
Storage: 24 months in unopened original packaging, at non-extreme temperature and humidity. Keep out of direct sunlight.

Tools and tools are easily cleaned with water before the paste has hardened. Cured or hardened product can only be removed by mechanical means.

The completion of the Beyem External Thermal Insulation System (ETICS) will be carried out with Beyem Cril coloured acrylic coating, from the company Rodacal Beyem, with ETA number 21/0061 under EAD 040083-00-0404. The yield shall be ≈ 2.0-2.5 kg/m2. The substrate shall be clean, sound, compact and dimensionally stable. Expansion joints shall be respected, where applicable, as well as the manufacturer’s general installation instructions.

For any information concerning safety issues in the use, handling, storage and disposal of chemical residues, users should consult the most recent version of the MSDS for the product. Disposal of the product and its packaging must be carried out in accordance with current legislation and is the responsibility of the final consumer of the product.