BEYEM CRIL FONDO Liso is a coloured acrylic primer for ETICS BEYEM system. Formulated with acrylic copolymers and micornized stone fillers that provide hardness and resistance to the product.
SMOOTH PERFORMANCE from 5 to 10 m²/layer (depending on surfaces). EAD marking 040083-00-0404 ETICS BEYEM System ETA 21/0061
EAD marking 040083-00-0404 ETICS BEYEM System ETA 21/0061
.
- Permeable to rainwater and permeable to water vapour
- Excellent coverage and performance
- High adhesion
- Ready-to-use
Prime/undercoat for ETICS BEYEM system. Absorption levelling agent for subsequent applications.
Supports useful for the application of BEYEM CRIL FONDO Liso are:
Other BEYEM products
The above-mentioned substrates must be sound, clean, free of paint residues, poorly adhered parts or substances that may hinder adhesion. All substrates must have adequate flatness. The substrate must not have any clear problems of dampness and, where applicable, must have completed its curing shrinkage and its maturing period must have been respected.
The substrate must be clean, clean, free of paint residues, poorly adhered parts or substances that may hinder adhesion.
At least 48 hours after the last smoothing coat of Beyem Adheterm, apply a coat of Beyem Cril Fondo Liso optionally diluted with 5% water, allowing it to penetrate the surface. Beyem Cril Fondo Liso can be applied by brush, roller or spray. This primer acts as an absorption equaliser and adhesion promoter for the subsequent Beyem Cril or Beyem Cril Polysiloxane finish. If the mortar application is to be cut, it is advisable to apply a second coat reinforcing the parts where the pattern will be marked.
- Do not apply below 5ºC or above 30ºC.
- Do not apply when there is a risk of frost, rain, strong winds or direct sun.
- Avoid using different batches on the same cloth, or failing that, it is advisable to mix 50% of the first pack with the contents of the second. This will prevent small variations in shade between batches from affecting the final result.
- Avoid leaving a cloth in the middle to avoid splices. Use working joints if necessary.
- For touch-ups on already painted substrates and to avoid marks, it is advisable to paint the whole cloth.
- It is not advisable to use colours whose solar radiation absorption coefficient (α) is greater than 0.7 unless the façade is permanently protected from solar radiation.
- Protect the upper edges of the cladding against the penetration of rainwater.
- Respect expansion joints.
Product identification details | |
Colour | According to colour chart |
Appearance | Viscous liquid |
Drying | 30 min |
Curing | 28 days |
Viscosity | 15.000 +/- 3.000 Brookfield |
Tariff code | 32091000 |
Product application data | |
Background | Beyem Cril Fondo |
Tool for extend | Steel trowel |
Tool for finishing | Plastic trowel |
Minimum thickness | 150 – 160micron in two coats (dry film) |
Performance | 0,15 – 0,24 Kg/m²(0,10 – 0,16 l/m²) |
Solvent | Water |
Cleanup | Water |
Repainting | As from 5 hours |
Final performance | |
Classification | ETA 21/0061 EAD 040083-00-0404 |
Liquid water permeability | w<0.086 (standard:<0.1 kg/m2·h0.5) |
Vapour permeability | SD<0.27 m (standard: SD<5 m) |
Abrasion resistance | Weight loss less than 681 mg (standard <3,000 mg) |
Adhesión | 2.1 N/mm2 (standard: >1.0 N/mm2) |
Resistance (falling mass test) | Seamless (2 kg from 1 metre) |
Chemical resistance | Complies with UNE-EN 1504:2005 (H2SO4 -Oil-Salt 20%-Leach-NaOH 20%-Gasoil) |
Water absorption | 1 h < 1 kg/m2 24 h < 1 kg/m2 |
Water vapour permeability | Equivalent air thickness ≤ 2 m (EPS/XPS) Equivalent air thickness ≤ 1 m (MW) |
Impact resistance | Class I, II or III depending on insulation and netting |
Behaviour in the face of thawing ice | The system is considered to be resistant to freeze/thaw cycles. |
Response to fire | F-class |
BEYEM CRIL FONDO LISO is packaged in 4 and 15L plastic buckets.
Storage: 24 months in sealed original packaging, at non-extreme temperature and humidity. Keep out of direct sunlight.
Storage: 24 months in closed original packaging, at moderate temperature and humidity.
Tools and tools are easily cleaned with water before the paste has hardened. Cured or hardened product can only be removed by mechanical means.
The primer coat of the Beyem Exterior Thermal Insulation System (ETICS) will be applied with Beyem Cril Fondo Liso coloured acrylic primer, from the company Rodacal Beyem, with ETA no. 21/0061 under EAD 040083-00-0404. The yield shall be ≈ 0.15 – 0.24 kg/m2 (0.10 – 0.16 l/m2). The substrate shall be clean, sound, compact and dimensionally stable. Expansion joints shall be respected, where applicable, as well as the manufacturer’s general installation instructions.
For any information regarding safety issues in the use, handling, storage and disposal of chemical residues, users should refer to the most recent version of the MSDS for the product. Disposal of the product and its packaging must be carried out in accordance with current legislation and is the responsibility of the final consumer of the product.